Every person is bound to have their personal perception on the subject of Tools You Need to Install a New Bathtub .
Mounting a tub isn't exactly brain surgery, but it does require strong plumbing, woodworking, and often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately challenging project. If the old tub is conveniently obtainable, the job can relocate speedily; if you need to open a wall surface to remove the old tub and also place the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to leave the old tub as well as set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is better to take into consideration employing one before you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly aid you mount a new bathtub in your washroom if you have actually currently gotten a brand-new bathtub and also do not require to change the setup of your previous water supply pipelines.
Your devices as well as product checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite problematic due to the restricted gain access to that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before going on to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using both wood boards under its feet, put the tub in the needed position. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bathtub till the spirit level reads degree.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet and also the regular outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's user's manual. Tiling and sealing around the tub must wait up until the bath tub has been used a minimum of when as this will settle it right into its final position.
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, creating the water to pass through the wall between the bath and the tiling, leading to problems with dampness and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can crack relatively very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article on How to Install a Bathtub Yourself through an acquaintance on a different web blog. So long as you enjoyed reading our article plz be sure to share it. Bless you for your time. Visit again soon.
Act now! Save later.